Sunday, May 3, 2020

DIY 3D Printer Project discussion active on Reboot Amateur Radio WhatsApp Group.

The Reboot Amateur Radio WhatsApp Group is currently very active during the current lock-down period. A wide variety of interesting discussion points are posted daily. 

The latest project discussed is constructing your own 3D Printer from scratch. I will post full detail soon on the Reboot Amateur Radio Blog but here is an appetite teaser:


The original Prusa Mendel that I built from a kit. The blue parts are reprinted replacement parts. Also the original gears I replaced with these printed grey herringbone ones. The direct extruder is for 3 mm filament.


The Delta printer based on the enlarged Rostock but with my own support structure design based on the Dobsonian telescope type of truss tube structure. All the parts were printed with the above first printer. The marine ply top and bottom are leftover cutouts from the 2 20 inch Dobsonians that I had built years earlier. The 6 gold looking thin pipes that support the print platform are from an FM antenna - thin walls and strong.


My current work-horse. An enlarged version of the original Prusa Mendel to give 300x300mm print plate. Parts are exactly the same as the original and were in turn printed on the Truss-tube Delta. Blue on print platform is blue painters tape on aluminium plate. Electronics all mounted on a DIN rail at the top. RPi in front followed by box with Mega and Ramps and then a third box holding a veroboard with external mosfet to switch high printbed heater current. Bowden extruder - also on Delta.


Recently completed printer the same as the enlarged work-horse shown previously.
All images courtesy of Johann Swanepoel, George.

All four printers comes from the stall of Johann Swanepoel a grand master in building his own 3D Printers. A lot of interest is expressed by the Group and talks are currently underway to launch a DIY 3D Printer project for interested group members. Johann will also be our tutor once the project starts. There is still planning to do and with the current lockdown in place, ordering and delivering of parts is rather difficult.


Bernhard  ZR6DBE 3D Drukker - My drukker is op commissioning fase, moes een of twee parte oorprint en moet dit nog insit. Sagteware is opgestel en loop. Bord word nie warm nie, het ander transistor bestel daarvoor. Bord elektronika is ok andersins. Lekker man!

More info will be published on this site soon.  

Roll your own Pofung/Baofeng Radio Programming Cable.

John ZS1ZR:  Ek soek n pofung prog. Kabel te koop?

Image above: Lional ZS6DPL

Image above:  Michael ZS004 George

Image above:  Keverne ZS1ABU

Image above:  Those of you having an Arduino UNO available. Reset the Arduino chip with the yellow wire and use just the serial - USB chip on board. Cables made up with ordinary twin screened audio cable. - Danie ZS1DBJ


Comments Reboot Group:  2020/04/29, 8:02 am - Llewellyn Hewitt "ZS003" George: Die baofeng kabel werk met die pofung radiod 2020/04/29, 8:03 am - John ZS1ZR George: Reg so.dis hy 2020/04/29, 12:50 pm - John ZS1ZR George: Is hy te koop? 2020/04/29, 12:52 pm - Lionel ZS6DPL Pretoria: Nee maar sal na lockdown nog kan kry 2020/04/29, 2:29 pm - Keverne Thurling ZS1ABU George: I have 2 sets of these for those in my area. One set has adapters for most radios. Works well with Chirp. 2020/04/29, 3:07 pm - Johan ZS1I: Keverne John ZS1ZR and Francois ZS1Q might be interested. 2020/04/29, 3:38 pm - Keverne Thurling ZS1ABU George: Looks like the one for the Boafeng. I can let them loan it and return when finished. I have Chirp files with all repeaters and simplex channels, Also have Chirp Layout of you want to work AMASATs. 2020/04/29, 3:40 pm - Johan ZS6IW Dennotter: Is it possible to send the files to my email Any costs involved 73 2020/04/29, 3:40 pm - Johan ZS6IW Dennotter: Battle to get chirp working on win 10 2020/04/29, 3:42 pm - Keverne Thurling ZS1ABU George: Email is free, can I use the email on SARL. 2020/04/29, 3:46 pm - Johan ZS6IW Dennotter: Not member of Sarl zs6iw.Jw@gmail.com 2020/04/29, 3:46 pm - Keverne Thurling ZS1ABU George: I can't really comment on how to fix it, but the recomendations I have seen is don't use the drivers that comes with the interface, let windows detect and install. I have just been lucky in that the ones I have have always worked. 2020/04/29, 3:47 pm - ZS1CQ Corrie Kreef: Ek het a poking een maar kry hom nie om te werk met chirp .water dryer moet ek he 2020/04/29, 3:52 pm - Keverne Thurling ZS1ABU George: Done, Sent you a copy of my UV5R radios, 2020/04/29, 3:52 pm - Johan ZS6IW Dennotter: Thanks a million 2020/04/29, 3:58 pm - Keverne Thurling ZS1ABU George: I'm not sure if you have used chirp before, but you know not to use these files as is, its better to clone from your radio first, save a copy, then cut and paste the info from my file or just input the info by typing it in. In that why you retain all the settings info from your radio. Just a tip that you could already know. 2020/04/29, 4:08 pm - Johan ZS6IW Dennotter: both files r corrupt or only opens by the program but thanks any way not at home now to use program 2020/04/29, 4:32 pm - Keverne Thurling ZS1ABU George: Yes, if you try and open them by double clicking, it will give you an err as the file extention is .img. Windows sees it as a corrupt disk image file. You have to open it from within Chirp. 2020/04/29, 4:58 pm - Keverne Thurling ZS1ABU George: Corrie, Iike I said, I've not encounted a problem with the two I have. But from what I have read about others that have a problem with the driver, is that you should let Windows decide. But if the incorrrect one is already installed, you apparently uninstall the driver with the Universal Serial Bus controller removed, then plug in again. Mine has the FTDI CHIP and the standard Windows USB to Serial Bus controller driver works. See, if nothing goes wrong, you learned nothing. 2020/04/29, 6:01 pm - ZS1CQ Corrie Kreef: Running win7 maybe should use my win10 

ARDF - Foxhunting on 145.000 - Nick ZS1N

I built a "fox" for 145.000. It uses an Arduino and a 2M handheld.






Reboot WhatsApp Comments:

2020/04/28, 11:24 am - Danie ZS1DBJ George: I was thinking about organizing a fox hunt after our lock in period. It could be a way of getting to know each other a bit better and also have some fun after the grim period. Unfortunately there will be driving involved in finding the fox, but one can also consider a walking search. I will supply the necessary Arduino, Boafeng radio and interface for the fox. What are your feelings about the idea. 2020/04/28, 11:29 am - Abe ZS1ZS Mosselbaai: I remember Fox Hunting in Jhb Highveld branch. We used 160m and the fox was sending CW 2020/04/28, 11:29 am - Abe ZS1ZS Mosselbaai: Today 2m or 70cms walking could be a good idea. Dankie Danie vir die gedagte. 2020/04/28, 11:40 am - Nick ZS1N Mosselbaai: My 2m doppler should still work as well. 2020/04/28, 11:45 am - Danie ZS1DBJ George: Hy is net USB en gebruik Prolific Ser_Usb dongle met CAT control. Die audio vanaf bordjie is nog steeds na rekenaar ear en mic. 2020/04/28, 11:49 am - Johan ZS1I: Dankie Danie. ARDF ja lekker daarmee gespeel. Nick jy sal moet wys hoe lyk daardie fox. Oom Jimmy dink ek het 'n fox timer wat ek gebou het by my oorgeneem. Werk met 'n PIC. 2020/04/28, 11:56 am - Danie ZS1DBJ George: It seems as if we have enough equipment to do a fox hunt. Will have a look after lock in.

Tuesday, April 28, 2020

2M Low Power TX For ARDF (Fox Hunting)


(NOT A ZS1I RESEARCH AND DEVELOPMENT PROJECT)
I decided to build myself this 2M low power ARDF transmitter as described by ON7YD.

This is a easy to build and low cost 144MHz mini transmitter that produces a remarkable 'clean' 144MHz signal up to 15 mW. It can also be used as exciter to drive a PA. In combination with a good UHF transitor a 2 transitor 200mW TX can be build or in combination with one of those power modules that are used in handies several Watts can be produced.
With a low cost 24MHz xtal the oscillator runs on the 3rd overtone (72MHz). The collector circuit acts as a doubler. In this type of oscillator the xtal oscillates well above it's natural frequency, resulting in a end frequency of +/- 144.070MHz for a 24MHz xtal. Any other 72MHz xtal can be used, but a lot of these xtals are 5th overtone. In this case L1 should be reduced to 0.47µH to avoid that the xtal will run on the 3rd overtone.
The oscillator is modulated with a mixture of AM and FM, so both AM or FM receivers can be used.


COMPONENT LIST:
IC1 4093 (CMOS)            
TI  2N918
T2  BC557C
X1  24 MHz
L1  1uH
L2/3  5 wind of 1mm wire, diameter 5mm, tapped at 1 wind from the cold end.
R1  39K
R2  1M
R3  10K
R4  330K
R5  1M
R6  1K
C1  47pF
C2  15pF
C3/4  3-20pF
C5  1n
C6  47n
C7  470n
C8  100n


The oscillator is built arround T1, with a 24 MHz xtal used on the 3rd overtone (72 MHz). The collector circuit acts as a frequency doubler and the critical coupled double band pass filter (L2, L3, C3, C4) makes sure that all (sub)harmonics are at least 40 dB below the carrier. C3 and C4 have to be adjusted for maximum output power.
With R2 the output power of the oscillator can be adjusted between 0.1 and 15 mW.
The 2 Schmitt-Trigger NAND gates of the 4093 produce a intermitted LF tone that is used to modulate the oscillator. The remaining gates are disabled by pulling their inputs to plus.
With R6 the modulation level can be adjusted.

Output power vs. supply voltage and current
supply voltage supply current output power
15 V 14mA 15 mW
12 V 11mA 9 mW
9 V 9mA 5mW
9 V 4.5mA 3mW
9 V 2.5mA 1mW





Above: Photos of the 2M Fox TX.

ABOVE:  Simple 2M Beam Antenna which I use to track the fox.


Above:  2M RX showing the fox in action on a fequency of 144.0875 Mhz NFM. 

(Click on images for larger view.)

NOTES:   The transmitter was tested extensively.  This transmitter is ideal for a small to medium range field.  This unit was tested in a 1km radius using the beam antenna for RX and a J-Pole as the TX for the transmitter. I could easily copy the signal even though there were buildings in the way.  The bonus of the antenna I used for receive is that you can either use the antenna horizontally or vertically polarized.  The TX emits a continues carrier with a very good audible beep.   This unit is ideal for a beginner TX to promote ARDF .  The bonus is that you can use several of these units in a small to medium field.  The unit is small and easy to construct.

Show us the Sound Card Interface you use for Digital Modes!!



In a recent post on the Reboot Amateur Radio WhatsApp Group I requested radio amateurs to provide me with photos of the Sound Card Interface that they use for Digital Modes in Amateur Radio.  Here are the original request:

"Show us the Sound Card Interface that you use for Digital Modes in Amateur Radio.  I would like to post photos on the Reboot Amateur Radio Blog.  It could be interesting to view all the various models currently used by radio amateurs.   I have photos of the following people's soundcards:  Danie ZS1DBJ,  Keverne ZS1ABU and Abe ZS1ZS.  Even if it is a commercial bought model.  Take a photo and post it on the group.  I am sure that there are many "brands" out there that would be of great interest to many of us.  Awaiting your photos!!"

And here are the photos:


CAT and USB Sound Card Interface of Abe ZS1ZS

RIGblaster Advantage USB Sound Card Interface Geoff ZS6C



USB Sound Card Interface of Nick ZS1N



USB Sound Card Interface of Thys ZS1TBP

SignaLink USB Sound Card Interface of Wessie ZS2A

Behringer Mixer Sound Card Interface of Willie  ZS2CC


USB Sound Card Interface of Keverne ZS1ABU




USB Sound Card Interface of Danie ZS1DBJ



Arduino USB Sound Card Interface of Johan ZS1I



Serial Sound Card Interface of Johan ZS1I

Monday, April 27, 2020

DIY Layout Creator - Vero Board Outlay



DIY Layout Creator (DIYLC in short) is freeware drawing tool developed with help of a large online community of DIY electronics enthusiasts. It incorporates many ideas that came from people using older versions of the application. The goal is to provide a simple interface and enough power to let the user draw schematics, board/chassis layouts and guitar wiring diagrams quickly and without a steep learning curve. Also, it is build around the flexible open source framework that may be used to draw pretty much anything. More information at: http://diy-fever.com/software/diylc/

Download version 1.18
Download complete layout collection for version 1.x




Comments from Reboot Group:  2020/05/01, 6:43 am - Francois ZS1Q George: More. Daars hy .. mooi so. Hou van jou beskrywing - sagte na harde 2020/05/01, 6:45 am - Danie ZS1DBJ George: Vir die eerste keer in my lang betrokkenheid (1963) met Vero board is dit Å„ absolute plesier met hierdie program. Dankie aan die ontwikkelaar. 2020/05/01, 7:00 am - Johan ZS1I: 2020/05/01, 8:11 am - Abe ZS1ZS Mosselbaai: Dit lyk na plesier. Het altyd op blokkies papier uitleg met n potlood gedoen.(vir die regstellings). en x waar track gesny word.  2020/05/01, 8:15 am - Danie ZS1DBJ George: Ek het so te werk gegaan op grafiek papier, Abe. Hierdie program gee vir my meer moed om kringe op Vero te doen. 2020/05/01, 8:17 am - Keverne Thurling ZS1ABU George: Not sure if I’m ever going to use it, but I have a nice size piece of Vero if you run out. 2020/05/01, 8:18 am - Abe ZS1ZS Mosselbaai: ek hou van daai program. Sal dit ook aflaai 2020/05/01, 8:22 am - Danie ZS1DBJ George: Morning Keverne. I will remember your offer. I use vero quite often for testing of circuits before creating the pcb. 2020/05/01, 8:24 am - Keverne Thurling ZS1ABU George: 2020/05/01, 8:42 am - Johann Swanepoel ZS2BVD George: Ek hou van veroboard en ek hou van daardie program. 2020/05/01, 9:08 am - André ZS1AFB van George: Ek is ook 'n vero board persoon. Thanks to Danie ZS1DBJ who provided the information relating to DIY Layout Creator.